return to homehome
Navigation
DP-103A Digital Master Reproducer
This product has been discontinued.
Features | Specifications
Specifications
DP-103A-IU Input Unit
Input/Output ConnectorsDigital input RCA pin jack: x 2
Remote control connector x 2
SCSI connector x 1
Digital Audio InterfaceType: SPDIF
Data format: 44.1 kHz 16 bit sampling (48 kHz with optional converters)
Connectors: RCA pin jack (for sides A and B)
Remote Control Interface (for DAT Recorders)Type: parallel communication
Control: PLAY, STOP, REWIND
Connectors: D-Sub 15 pin (for sides A and B)
SCSI InterfaceTransfer type: 4 MB/s asynchronous
Connector: single end 50-pin connector
CD-ROM DriveSupports CD-DA format
Hard Disk DriveRemovable type
Power Supply100/110/117/220/240 VAC ±5%, 50/60 Hz
Power Consumption60 VA (max. 80 VA)
Dimensions482 x 177 x 435 mm (W x H x D), 19" rack mount case
Weight8 kg
DP-103-MU Memory Unit
Playback Speed64x, 80x, 128x (= optional)
No. of Tracks4 tracks (2 channels)
Input/Output ConnectorsAnalog playback output connector (4 channels)
SCSI connector
Amplifier control connector
Analog Playback OutputConnector: BNC x 4
Signal Level: max. 5 Vp-p (full-bit)
SCSI InterfaceTransfer: 4 MB/s asynchronous
Connector: Single-end 50-pin connector
Amplifier ControlCue tone oscillation on/off
Copy rate selection (x64, x80, (x128 option))
Bias selection (1, 2, 3, 4)
Equalization selection (1, 2, 3, 4)
Dolby HX Pro on/off
Production count
Data Transfer SpeedSCSI to memory: 16-bit DMA transfer
(data set time depends on drive's internal transfer speed. Currently approx. 16 times real time, 3.5 minutes for C-60)
Memory to D/A converter: 64-bit
Power Supply100/110/117/220/240 VAC ±5%, 50/60 Hz
Power Consumption220 VA
(10 MEMORY boards installed: max. 240 VA, 16 MEMORY boards installed: max. 300 VA)
Dimensions482 x 310.4 x 506.6 mm (W x H x D), 19" rack mount case
Weight20 kg
DP-103-AU Amplifier Unit
Record Input Signal (Chs 1-4)Connector: BNC unbalanced
Input Impedance: 1 kΩ
Max. Input Level: 5 Vp-p (at full-bit swing)
Record Output Signal (Chs 1-4 x 2)Connector: BNC unbalanced
Ref. Output Level: 0 dBu (75Ω loard)
Max. Output Level: +20 dBu
Level Control-∞, -20 to 0 dB, 1-dB steps
Tone ControlFrequency: 5 to 10 kHz (11 points)
Level: 0 to +6 dB, in 0.6-dB steps
Cue Tone Oscillator10 Hz x 64, x 80, (x 128)
(interlocked to copy rate. Frequency, level, and oscillation timing are adjustable)
Low-Cut FilterFrequency: 20 Hz x 64, x 80, (x 128). Slope: 24 dB/oct.
Dynamic Range96 dB
Frequency Response25 Hz to 20 kHz +0.5/-1 dB (64x/80x, low-cut filter ON)
20 Hz to 20 kHz ±0.5 dB (64x/80x, low-cut filter OFF)
THDLess than 0.2% (0 VU (0 dB), 1 kHz)
CrosstalkLess than 70 dB
Channel SeparationBetter than 70 dB
Monitor Output Frequency Response20 Hz to 20 kHz ±1 dB (normal speed)
Power Supply100/110/117/220/240 VAC ±5%, 50/60 Hz
Power Consumption80 VA (max. 100 VA)
Dimensions482 x 221.5 x 511.5 mm (W x H x D), 19" rack mount case
Weight13 kg
DP-103-SU Speaker Unit
Monitor Signal InputInput impedance: 10 kΩ
Input level: max. 2 V rms (full-bit)
Connectors: RCA pin jack pair x 2 (for DAT 1 and DAT 2), Stereo phone jack x 1 (DUP SIG)
Speaker Output3 W + 3 W (8Ω)
Power Supply100/110/117/220/240 VAC ±5%, 50/60 Hz
Power Consumption10 VA (max. 20 VA)
Dimensions482 x 149 x 198 mm (W x H x D), 19" rack mount case
Weight5 kg
System Rack
Dimensions1,510 x 594 x 638 mm (H x W x D, with each unit in it)
Net Weight132 kg
Operating EnvironmentTemperature: 15 to 35°C, Relative Humidity: 20 to 80%
Storage EnvironmentTemperature: -20 to 45°C, Relative Humidity: 10 to 80%
Optional Accessories
A1233Equalizer Amplifier Unit (for DP-85C, 64x)
CY1088Front Panel Handle (1 pair)
PB-4ZUATMEMORY Board (for expansion)
PZ4Z041Removable HDD with Carrier
ZA-45WSample Rate Converter Kit (factory option)
ZA-99SMaster A/B Switch Assembly (internal type)
CB-515AMaster A/B Switch Assembly (unit type)
NOTE: Regarding copied tape quality, refer to the operation manual or specifications of the slave recorder.
Specifications are subject to change without notice or obligation.